John Deere 450g Parts Manual
This seal kit is used on multiple John Deere Tractors where water pumps with casting # R70437, R100812 or R78286 is used. Plastic installer included. For tractor models 450, 450B, 450C, 450E, 450G, 455D, 455E, 455G, 480, 480A, 480B, 480C, 482C, 490, 490E, 495D, 500, 500A, 500B, 500C, 510, 510B, 510C, 510D, 515B, 540, 540A, 540B, 540E, 540G, 548D, 548E, 548G, 544, 544A, 544B, 544C, 544D, 544E, 544G, 550, 550A, 550B, 555, 555A, 555B, 570, 570A, 570B, 590D, 595, 595D and 610B. (Part No: AR101549) $9.99 Electrical System. For 340D, 344E, 410C, 410D, 440C, 450E, 450G, 455E, 490D, 493D, 510B, all with 4.276D Diesel, 300 Series, 4 cylinder, 4.19' bore, 1.62' pin.
Major Overhaul Kit includes: Piston Liner kit, Main Bearings set, Crank Seals, Connecting Rod Bearings/Bushings/Bolts set, Cam Bushing, Gasket Overhaul set. When ordering, specify in comments Main Bearing Size of Standard,.010,.020 or.030, Thrust Bearing Size of Standard,.010,.020 or.030, Connecting Rod Bearing Size of Standard,.010,.020, or.030. Camshaft Bushing of out dia. 020 O/S or in dia. (Part No: RE63694) $1178.30.
Welcome to Hudon's John Deere 450 Parts Page - Hard to find new and used parts for John Deere 450 dozers, loaders and crawlers - Buying and Selling Used 450's.
For 340D, 344E, 410C, 410D, 440C, 450E, 450G, 455E, 490D, 493D, 510B all with 4045D Diesel, 300 Series, Liter designated, 4 cylinder, 4.19' bore, 1.62' pin. Major Overhaul Kit includes: Piston Liner kit, Main Bearings set, Crank Seals, Connecting Rod Bearings/Bushings/Bolts set, Cam Bushing, Gasket Overhaul set. When ordering, specify in comments Main Bearing Size of Standard,.010,.020 or.030, Thrust Bearing Size of Standard,.010,.020 or.030, Connecting Rod Bearing Size of Standard,.010,.020, or.030.
Camshaft Bushing of out dia. 020 O/S or in dia. (Part No: RE63694) $1178.30. For 6400, 6410, 6500, 6500L, 6510, 6700, 340D, 344G, 410C Turbo, 410D Turbo, 440C, 444E, 444G, 448D, 450E, 450G, 455E, 455G, 490E, 495D, 548D, 510C, 540D, 550A, 550B, 550G, 555A, 555B, 555G, 590D, 595D, 610B, 610C, 650G, all with 4045T Diesel, 300 Series, Liter designated, 4 cylinder, 4.19' bore, 1.62' pin. Major Overhaul Kit includes: Piston Liner kit, Main Bearings set, Crank Seals, Connecting Rod Bearings/Bushings/Bolts set, Cam Bushing, Gasket Overhaul set.
When ordering, specify in comments Main Bearing Size of Standard,.010,.020 or.030, Thrust Bearing Size of Standard,.010,.020 or.030, Connecting Rod Bearing Size of Standard,.010,.020, or.030. Camshaft Bushing of out dia. 020 O/S or in dia. (Part No: RE61612) $1127.39. For 6010, 6110, 6110L, 6210, 6210L, 6310, 6310L, 6310S, 6405, 6410, 6410L, 6410S, 6510, 6510L, 6510S, 6605, 6610, 450G, 455G, 550G, 555G, 650G, 120, all with 4.5D or 4.5T Diesel, 4.5L OEM, Power Tech Engine, Piston Marked RE55512, bore 4.19', 1.62' pin. Major Overhaul Kit includes: Piston Liner kit, Main Bearings set, Crank Seals, Connecting Rod Bearings/Bushings/Bolts set, Cam Bushing, Gasket Overhaul set.
When ordering, specify in comments Main Bearing Size of Standard,.010,.020 or.030, Thrust Bearing Size of Standard,.010,.020 or.030, Connecting Rod Bearing Size of Standard,.010,.020, or.030. (Part No: RE66094) $1141.54 Engine Parts. This Camshaft replaces those marked T20013 or T20014. It has multiple John Deere agriculture and industrial applications.
Used so some of the following diesel and turbo diesel engines: 4.202, 4.218, 4.239, 4.267, 4039D, 4039T, 4045D. Verify casting numbers before ordering. Does not include tach drive. Replaces R82820, T20013 or T20014. Uses R81513 Screw In Tach Drive, not included, not available through YT.
(Part No: R82820) $125.72 Universal Parts and Accessories Category: Accessories / Supplies Accessories / Supplies. Lucas Hub Oil was formulated to stop leaks in steering axles and trailer hubs on heavy duty trucks. It also allows hubs to run on a marginal amount of oil in case of a blown seal or poor maintenance. It is an excellent gear lube for racing or heavy duty applications.
Key benefits slows leaks, prevents downtime, extremely heat resistant, Very long lasting. (Part No: LU10088) $10.56 Electrical System - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 & newer). Just call us at 800-853-2651. Lucas Assembly Lube (4 oz). Designed to be used as an initial lubricant to metal surfaces.
It mixes with any oil and will not plug filters. This product clings to all surfaces and is an excellent rust inhibitor, allowing long term storage for all parts.
It is useful wherever tension or torque is applied. Key Benefits are: Use to pre lube camshaft, bearings, lifters and valve train. Prevents seizing, galling and scuffing perfect for engine lding, super slick and tacky, easy to use, excellent rust inhibitor, excellent for long term storage, contains Zinc, Moly and other extreme pressure additives for maximum protection during engine break-in. (Part No: 10152) $5.00 Engine Parts - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor). NOTE Engine Rings - Don't see the correct ring set for your tractor?
Give us a call and ask for a Hastings Ring Set (made in USA). We need the following information to correctly find the set you need: 1. Engine size & type (Ex: 233 CID Gas) 2. Number of engine cylinders, 3. Cylinder bore size, 4. Number and size of compression rings for each piston (Ex: (2) 3/32'), 4. Number and size of oil rings for each piston (Ex: (1) 5/32').
NOTE Exhaust System. Lucas Fuel Treatment is formulated for both gasoline and diesel engines, carbureted or fuel injected.
It gives your fuel system what it really needs - a blend of super slick oils and additives with a high detergent action that allows the engine to operate at maximum efficiency. Also, it cleans and lubricates the carburetor and injectors and causes the fuel to burn more thoroughly for increased power and less fuel consumption. Lucas Fuel Treatment should definitely be used in vehicles that require leaded fuel because it actually replaces the benefits of lead in gasoline without causing harmful emissions.
Use it to pass smog tests. Finally, it totally neutralizes the harmful effects of low sulfur diesel fuel.A powerful blend of oils and additives that contain no SOLVENTS. Designed to increase power and fuel mileage and also lower exhaust emissions through a more complete combustion.
(Part No: LU10003) $10.67. Comes assembled complete with hardware. Easier hookup, spring loaded locking device. Adjustable top link ball bracket. Includes 7/8 inch mounting pins and adapter bushings, 27-1/4 inches width, 3-1/2 inch x 3-1/2 inch beam. This is ONLY for tractors that have, a three point hitch already installed.
An additional shipping charge of $60 will apply due to the weight of this item. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: HF141101) $227.70. Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inch diameter, 8 inches overall length, 7-1/4 inches to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405.
Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Part No: 12269) $176.32.
Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inch diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Part No: 12269) $176.32.
Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel.
Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters.
With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Part No: BH215) $106.08. 6 inch x 9 inch tail wheel assembly with laminated tire, less hub. 4 inch pilot, 5 bolt holes, 5-1/2 inch bolt circle. 5-1/4 inches wide, 21 inch outside diameter, 74#. Used mostly on pull Bush Hog models of the following series mowers: 109, 115, 126, 160, 166, 205, 206, 207, 220, 255, 256, 257, 268, 305, 306, 307, 310, 315, 405, 406, 502, 600, 1109, 1115, 1126, 1206, 1207, 1209, 1220, 1226, 1257, 1305, 1306, 1307, 1310, 1315, 1405, 1406, 1600, 2315, 2415, 2510, 2512, 2610, 2614, 2615, 3108, 3209, 3368, 3414, 3610, 4214, 4215, 12610, 12615, 13710, CR14R, CR20F.
(Part No: 294) $124.93. 60 inches wide x 65 inches long, molded from virtually indestructible flexible U.V. Stabilized polyethylene, exclusive socket mounting system for torsion bars, no mounting bolts pass through molding.
Available in green, white, orange, blue, or red. Please specify in comments section which color you need. Hardware to mount to your ROPS sold separately. Additional $150.00 shipping due to weight and size.
IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: B257X) $430.31. 45 inches wide x 60 inches long. Molded from virtually indestructible flexible U.V. Stabilized polyethylene, exclusive socket mounting system for torsion bars NO mounting bolts pass through molding.
Available in white, green, orange, blue, and red please specify in comments section which color you prefer. Hardware to mount to your ROPS sold separately. Additional $150.00 shipping due to weight and size. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: B257XSTD) $374.50.
John Deere 450g Parts Manual
Deluxe Umbrella comes with universal mounting bracket. Four spring steel bows are locked into place with individual spring clips, providing ease of operation and a rigid framework. Frame constructed of tubular steel.
All metal parts are zinc plated for rust resistance. 54 inch square cover is made of durable polyester material.
Each corner is double reinforced. AVAILABLE IN RED, YELLOW, ORANGE, WHITE or BLUE. State color desired in comments section of order form when ordering.
John Deere 450g Lgp Parts Manual
(Part No: TU56-X) $155.22. A pure petroleum multi-use oil supplement. Controls noise, heat and wear in manual transmissions and differentials. Number one in the heavy duty and high performance industries. Lucas Oil Stabilizer is a 100% petroleum product formulated to eliminate dry starts and reduce friction, heat and wear in any type of engine. It allows motor oils a higher degree of lubricity which reduces oil consumption and operating temperatures.
Use Lucas Oil Stabilizer in gear oil to stop leaks, reduce operating temperatures and increase the life of the gear oil. Since it is pure petroleum. Key Features Increase oil life at least 50% longer, Reduces oil consumption, Eliminates dry starts, Raises oil pressure, and Increases power and miles per gallon. (Part No: LU10001) $15.12 PTO / Driveline.
AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. Tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore.
Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Part No: AB4111WY) $187.82. AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. Tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch.
1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length.VERIFY LENGTH BEFORE ORDERING. (Part No: AB4111K33) $288.01.
Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is Black. Additional $30 shipping due to size and weight.
IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: TS1050ATSP) $89.37. BLUE Universal application leatherette suspension seat. For most compact, agricultural and industrial tractors. Adjustable base for 5 different mounting angles, internal suspension weight adjustment, special slotted base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, adjustable slide track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL.
PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is BLUE. Add $15 additional shipping per seat due to size and weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: TS1060ATSP) $89.37.
Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is BLACK. (Part No: TS1075ATSP) $89.37.
This Universal Vinyl seat has Multiple mounting holes, ranging from 4 inch to 11 inch center to center (front to back) and 6-1/2 to 13 inch center to center (side to side). Customer needs to verify it will work for their tractor. An adapter plate may need to be made for some models. Slide track for forward/rear adjustment. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. (Part No: TS1100) $117.53.YELLOW.
Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. Add $15.00 additional shipping due to weight.
IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: TS1040ATSP) $88.39 Sheet Metal / Body Parts. This Power Steering Pump replaces the Eaton style belt driven Power Steering Pump. It also replaces Eaton part numbers: 503-1005-005, 20928 and P761.
This is a Redesigned Pump that uses a bearing instead of original bushing. It can also be adapted to tractors using Char-Lynn power Steering with an Eaton Pump. Please note that this pump does not include brackets, top mounted reservoir, or pulley.
Some applications will require a new pressure hose to be made for a 5/8-18 inch inverted flare type fitting. The shaft diameter measures.670 inches. The shaft length, where the pulley mounts measures.575 inches. There is a 2 inch thick pump housing where the bracket bolts on. Pressure is preset at 1.32 GPM. (Part No: S03-1003) $384.33. With embroidered John Deere logo.
(Part No: JDGR) $19.95 Call 800-853-2651 to Order Or Click the 'Add to Cart' Button Customer Service Monday - Friday 9:00-6:30pm EST Order online anytime! Your Shopping is YESTERDAY's TRACTORS has been a leading tractor parts supplier on the internet since 1995. Join thousands of happy customers who have purchased parts and more for their antique tractor from us! Copyright © 1997-2018 Yesterday's Tractor Co.
Antique Tractor Headquarters All Rights Reserved TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. Products and within the Yesterday's Tractor Co. Websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Request our catalog Call 563-323-2295 Davenport Tractor manufactures parts for the antique John Deere Tractor line. Replacement parts for Two-Cylinder and New Generation tractors now becomes easier to find Our location in the Davenport, Iowa area is perfect as a shipping location.
Orders delivered to either coast of the USA are very reasonable Our replacement Two-Cylinder parts are made and inspected in the Quad City area by retired John Deere employees that were responsible for making the original parts. You can't get any more authentic. In the rare chance a return is necessary, our customer service department is sure to please with easy no phone call returns. There is never a restocking fee. Try that at a John Deere parts counter.
This Operators Manual for the John Deere JD450 Crawler Tractor is a finely produced document. Drilled to fit a standard 3 ring binder, and will last for years, even when over extended. The cover is heavy stock design. Inside the pages are printed on heavy sepia toned paper with 'cleaned' images.
John Deere 450 Bulldozer Manual
A 'must have' for adjustments and routine maintenance to your JD450 Crawler Tractor. Manual includes sections on 'Before Starting', 'Tractor Operation', 'Starting Tractor', 'Care of Tractor'. This Operators manual - OM-T25106 - was supplied with the tractor when purchased.
This new release of 5 Star Quality manuals represent a quantum leap in quality. They are printed on an extremely high resolution printer capable of producing image resolution never before seen in this line of manuals. Our in-house printers are capable of producing images of higher quality than the presses originally used to produce these documents, with finer inks, which results in manuals that produce eye-popping image and text quality. You can feel comfortable knowing you own the best, 5 Star Quality tractor manuals produced in the USA and sold directly by the manufacturer. The Davenport Tractor Inc.® site is dedicated to preserving our farming heritage.
We actively farm with antique John Deere Two Cylinder tractors. John Deere parts tractors have been in our collection for many years. Our mission is to provide you the highest quality reproduction John Deere Parts with reliable supplies at a reasonable cost. Davenport Tractor ® is constantly trying to help you find the rare parts for your John Deere tractor that are required to keep your antique Tractor running for years. In most cases we are the part manufacturer.
We specelize in replacment John Deere parts, Antique Tractor Parts, Replacement Catalogs, A perfect reference for all of those technical 'how to' questions. We have added new Parts Catalogs and Operators manuals for models Oliver, Farmall, Case, International Harvester, Ford, McCormick-Deering, and many others. We have added our automatic gasket cutter which allows us to sell separate gaskets as demand and production of our dies allows. Our new line of John Deere Tractor Owners manuals in our tool box series, formatted like the originals to be displayed in the tractor tool box, which is a great way to show off your newly restored tractor.
This also tells your audience that you paid special attention to your tractor restoration details. LP-Gas fuel parts are becoming more hard to find all the time. We are producing a rebuild kit for the Century M-4 LP Converter, we have been for a few years now with great feedback. And in 2013 we are introducing a similar kit to rebuild the H LP-Gas converter found on the John Deere Waterloo Tractor line of antique Tractors. We don want to let the cat out of the bag on all of the planned Tractor Parts we have in store for this year. Closely watch Davenport Tractor website and check back often, we commit more of our income to providing new products to the tractor restoration hobby than anyone else.
A great line up of new products this summer, and a new product catalog coming your way soon. As always You the customer is why we are in business. We are commited to priceing our product fairly and treating our customers with respect, and the highest quality products possable.